 |
|
CPU
-Intel® Pentium® 4 Processor with Hyper-Threading Technology
- 800MHz/533MHz system data bus
-Intel® Pentium® 4 Northwood processor
- 533MHz/400MHz system data bus
-Intel® Celeron® Northwood processor
- 400MHz system data bus
CPU Socket
-Socket 478
Chipset
Intel® 875P chipset
- Intel® 82875P Memory Controller Hub (MCH)
- Intel® 82801ER I/O Controller Hub (ICH5R)
System Memory
Supports dual channel (128-bit wide) memory interface
- Each channel supports 2 DIMM sockets
Supports up to 4GB system memory
Supports Dynamic mode to optimize system performance
Synchronous operation with processor system bus
- PC2100/PC2700/PC3200 (DDR266/DDR333/DDR400) with 800MHz FSB CPU (supports PAT mode).
DDR333 will run at 320MHz memory frequency when used with 800MHz FSB CPU.
- PC2100/PC2700 (DDR266/DDR333) with 533MHz FSB CPU
- PC2100 (DDR266) with 400MHz FSB CPU
Supports ECC/non-ECC DIMMs
Supports unbuffered DIMMs
BIOS
Award BIOS, Windows® 98SE/2000/ME/XP Plug and Play compatible
Genie BIOS provides:
- CPU/DRAM overclocking in 1MHz stepping
- AGP/PCI/SATA overclocking
- CPU/DIMM/AGP overvoltage
4Mbit flash memory
CMOS Reloaded
Power Management
Supports ACPI STR (Suspend to RAM) function
Wake-On-Events include:
- Wake-On-Keyboard/Mouse
- Wake-On-USB Keyboard
- Wake-On-Ring (external modem)
- Wake-On-LAN
- RTC timer to power-on the system
AC power failure recovery
Hardware Monitor
Monitors CPU/system temperature and overheat alarm
Monitors CPU/1.5V/5VSB/VBAT/3.3V/5V/±12V voltages and failure alarm
Monitors CPU/chip/second fan speed and failure alarm
Automatic chip/second fans on/off control
Read back capability that displays temperature, voltage and fan speed
CPU Fan Protection function monitors the CPU fan during system boot-up
CPU Temperature Protection function monitors CPU temperature during system boot-up
Audio
20-bit stereo full-duplex codec with independent variable sampling rate
High quality differential CD input
True stereo line level outputs
S/PDIF-in/out interface
6-channel audio output
LAN
Uses 82547EI Gigabit LAN CSA interface
Full duplex support at both 10, 100 and 1000 Mbps
ATA RAID
Uses HighPoint 372N RAID controller
RAID 0, 1, 0+1 and 1.5
PCI IDE
Supports ATA/33, ATA/66 and ATA/100 hard drives
PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)
ICH5R SATA IDE with RAID
Supports two SATA (Serial ATA) interfaces which are compliant with SATA 1.0
specification (1.5Gbps interface)
Supports RAID 0 and RAID 1
AGP
Supports 1.5V AGP 8x (2.13GB/sec.) and AGP 4x (1066MB/sec.) for 3D graphics
applications (AGP 2x and 3.3V AGP card are not supported)
Supports AGP 3.0 and AGP 2.0 spec.
Rear Panel I/O Ports
4 USB 2.0/1.1 ports
1 RJ45 LAN port
1 DB-9 serial port
1 DB-25 parallel port
1 mini-DIN-6 PS/2 mouse port
1 mini-DIN-6 PS/2 keyboard port
2 RCA jacks for S/PDIF-in and S/PDIF-out
2 audio jacks for center/bass and rear out
3 audio jacks: line-out, line-in and mic-in
I/O Connectors
2 connectors for 4 additional external USB 2.0/1.1 ports
1 front audio connector for external line-out and mic-in jacks
1 connector for an external game/MIDI port
2 internal audio connectors (CD-in and AUX-in)
1 S/PDIF-in/out connector for optical cable connection
1 connector for IrDA interface
2 RAID IDE connectors
2 Serial ATA connectors
2 IDE connectors
1 floppy connector
2 ATX power supply connectors
1 Wake-On-LAN connector
4 fan connectors for CPU fan, chassis fan, second fan and chip fan
1 diagnostic LED connector for external 4 diagnostic LEDs display
EZ touch switches (power switch and reset switch)
Expansion Slots
1 AGP slot
5 PCI slots
Compatibility
PCI 2.2 and AC ’97 compliant
Intel AGP version 3.0
PCB
4 layers, ATX form factor
30.5cm (12.05") x 24.4cm (9.6")
All specifications above are subject to change without prior notice.
This product categorized in:
|
|
|
|
|
 |
|
